Quantity:
Details:• Size: 90x90x90mm• Pump Speed: 1,500 LPH (Variable)• Max Temp: 60° C• Delivery head: 3.7m• Power Consumption: 23W• Voltage: 12V 4Pin Molex• Compact size allows installation almost anywhere in the caseThis pump is RPM adjustable• P1 = 1.800 revs./min• P2 = 2.550 revs./min• P3 = 3.300 revs./min• P4 = 4.050 revs./min• P5 = 4.800 revs./minCompatibility:• For Use with 1/2" ID Hose
dB-1 Compact 12v Ultra Quiet Compact PumpDetailed Description:The dB-1 offers ultra low noise (20db), small size and is perfect for low restriction multiple block cooling loops or CPU/GPU only Cooling. This pump works very well paired with the high flow rates of our FuZion CPU block.Features:Compact case Designed specifically for PC cooling Very low noise output (20db) Virtually no vibration output Mag drive ceramic bearing motor assembly Advanced rotor design provides quick priming Low power consumption and low heat output Brackets included for multiple mounting configurations G 1/4" Barb threading Pre-Installed 1/2" or 3/8" Nickel Plated Hi-Flow barbs Standard Motherboard 3-pin connection Can be submersed Specifications:Dimensions 2.3" x 1.8" x 2.4" Voltage DC 12V Voltage Range DC 8V ~ DC 13.2V Starting Voltage DC 8V Amp 0.5 Motor Ceramic Bearing LPH 500 Max Head 2M Noise 20db MTBF 50,000 hrs Temp Range 0 ~ 60C Connector 3 pin/w signal Weight .2 LBS
This product has gone under new revision, with more power output.This pump is the first pump worldwide, which can be installed in mass-produced water-cooled workstations, and it is ideally suitable for the water cooling of processors and electronic components. Due to its size and output, a multitude of applications are available. This pump is an electronically commuted ball-motor pump, with running times of more than 50.000 hours at 12 V. The only flexible part of a ball-motor pump is a sphere-formed rotor-/runner unit, which is propped up against an extremely hard, wear-resistant ceramics bearing ball. A conventional axle with journal bearing and shaft sealing is not available. The spherical bearing of the rotor-/runner unit on the ceramics bearing ball provides a lot of advantages: a development of the bearing play – and thus a noise increase - is theoretically not possible. The pump is silent over the whole running time. The bearing is self-adjusting. It is lubricated directly by the delivery medium (wet-running pump). There is basically no need for maintenance. Since the rotor is always held magnetically in the intended position, smaller dirt particles are no problem. Blocking of the pump is not possible under normal conditions. Even after lengthy downtimes a safe approach is given. The permanent magnetic rotor/ runner unit is propelled by a magnetic field, which is produced by the surrounding stator. This is built entirely around the rotor. The entire pump is thus with 38 mm only a little higher than the stator itself. It easily fits into all conventional PC, Barebone and Mini PC cases. A separate magnetic shielding is not necessary under normal conditions. Normally, a separate magnetic shielding is not necessary. The ball motor principle enables an economical enterprise with comparatively high achievements. The tension variation can easily regulate the DDC direct current pump over a large capacity range. All medium-affecting parts are completely corrosion resistant.Technical data:Dimensions: (WxLxH) 62x62x38mm (without connections)Motor construction type: electronically commuted ball-motor Working voltage: 12 V DC VoltageAdmissible voltage area: 6 to 13,2 VDelivery height: at 12V: 4,7mMax. delivery rate: 600L/hDelivery media: water, water-/glycol compoundsMax. system temperature: 60° CMedium-affecting parts: stainless steel 1.4571, PPS-GF40, EPDM O-sealing rings, alumina, hard carbonConnections: 2x 3/8" hose connection
Note: this item does not come pre-assembled... click Here for video assembly instructions (Quicktime format - ~10MB).Specifications (w/18W DDC-2):Model: DDCT-01sTop Dimensions: 67mm x 62mm x 23mmMateriel: Black Delrin/AcetalSurface Finish: Smooth & MatteInlet/Outlet Thread Type: G1/4 (1/4" BSPP)Max. Head Pressure (at 12V): 8.2 psig (18.91 feet - 5.76m)Max. Discharge (at 12V): 4.11 GPM (246.6 GPH - 15.56 LPM/933.5 LPH)Included Accessories: (2x) 1/2" D-Tek High-Flow fittings or 1/2" EK High-Flow fittings & (4x) 25mm Stainless Steel M4 Phillips Head screwsStock DDC-2 (18W) Specifications:Nominal Voltage: 12 VDCOperating Voltage range: 8 - 13.2 VDCMinimum Starting Voltage: 9 VDCNominal Power (@12 V): 18 WNominal Current (@12 V): 1.46 Amp Motor Type: Electronically commutated, brushless DC, spherical motorMaximum Head: 20.2 ft (6.1 m)Maximum Discharge: ~ 120 GPH (454 LPH)Connection Size: 3/8" barbsMaximum Pressure: 22 PSI (1.5 BAR)Temperature Range: Up to 140°F (60°C)Noise Level (Swiftech's Results): 30 ~ 32 dBA in a quiet room @ 2'Electrical Connector: 4pin MolexWeight: 7.3 oz (207 gr.)RPM Sensor: 3 pin connector
EK-DDC X-TopThreads: G1/4Dimensions: 67×62×20mmIncluded:4x M4x24mm screwsBarbs Included (select type)Stock DDC-2 (18W) Specifications:Nominal Voltage: 12 VDCOperating Voltage range: 8 - 13.2 VDCMinimum Starting Voltage: 9 VDCNominal Power (@12 V): 18 WNominal Current (@12 V): 1.46 Amp Motor Type: Electronically commutated, brushless DC, spherical motorMaximum Head: 20.2 ft (6.1 m)Maximum Discharge: ~ 120 GPH (454 LPH)Connection Size: 3/8" barbsMaximum Pressure: 22 PSI (1.5 BAR)Temperature Range: Up to 140°F (60°C)Noise Level (Swiftech's Results): 30 ~ 32 dBA in a quiet room @ 2'Electrical Connector: 4pin MolexWeight: 7.3 oz (207 gr.)RPM Sensor: 3 pin connector
This product has gone under new revision, with more power output.This pump is the first pump worldwide, which can be installed in mass-produced water-cooled workstations, and it is ideally suitable for the water cooling of processors and electronic components. Due to its size and output, a multitude of applications are available. This pump is an electronically commuted ball-motor pump, with running times of more than 50.000 hours at 12 V. The only flexible part of a ball-motor pump is a sphere-formed rotor-/runner unit, which is propped up against an extremely hard, wear-resistant ceramics bearing ball. A conventional axle with journal bearing and shaft sealing is not available. The spherical bearing of the rotor-/runner unit on the ceramics bearing ball provides a lot of advantages: a development of the bearing play – and thus a noise increase - is theoretically not possible. The pump is silent over the whole running time. The bearing is self-adjusting. It is lubricated directly by the delivery medium (wet-running pump). There is basically no need for maintenance. Since the rotor is always held magnetically in the intended position, smaller dirt particles are no problem. Blocking of the pump is not possible under normal conditions. Even after lengthy downtimes a safe approach is given. The permanent magnetic rotor/ runner unit is propelled by a magnetic field, which is produced by the surrounding stator. This is built entirely around the rotor. The entire pump is thus with 38 mm only a little higher than the stator itself. It easily fits into all conventional PC, Barebone and Mini PC cases. A separate magnetic shielding is not necessary under normal conditions. Normally, a separate magnetic shielding is not necessary. The ball motor principle enables an economical enterprise with comparatively high achievements. The tension variation can easily regulate the DDC direct current pump over a large capacity range. All medium-affecting parts are completely corrosion resistant.Technical data:Dimensions: (WxLxH) 62x62x38mm (without connections)Motor construction type: electronically commuted ball-motor Working voltage: 12 V DC VoltageAdmissible voltage area: 6 to 13,2 VDelivery height: at 12V: 4,7mMax. delivery rate: 600L/hDelivery media: water, water-/glycol compoundsMax. system temperature: 60° CMedium-affecting parts: stainless steel 1.4571, PPS-GF40, EPDM O-sealing rings, alumina, hard carbonConnections: 2x 1/4" hose connectionCharacteristics: Plexi cover, 5mm LED drilling, incl. uncoupling set for 3,5” slots. The pro-cover is not preinstalled!User’s recommendation: the cover connection side should be mounted on the lateral sides of the connecting cable.Note: With the addition of the 4 piece damper kit (not included but available using the in the drop down menu), the pump can be mounted in the hard drive cage or 80mm fan.
The optimal water tank for the Laing DDC pump (new revision with more power)This water tank is thus designed, that you can mount it and decouple it in any imaginable form. With the uncoupling sets (enclosed), the Laing can be mounted completely decoupled in any 3,5”slot, for example at the bottom side, by means of the standard uncouplings or even better, it can be installed in place of 80mm fans. Also for the attachment any position is possible, let your fantasy run free. The water tank has 5mm LED drillings for Case Modders. and a capacity of 110ml. With this new version, the pump can absorb absolutely free of blow holes.Technical data:Dimensions (LxWxH): 80 x 80 x 70mm (without connections, without pump)Weight: 400gMaterial: Röhm Plexiglas GS Mounting: 8x uncouplings Connections: 2x G1/4" inch threadSealing: 1x G1"- oil inspection glassVolume: 110mlIncluded in delivery:1x DDC-water tank with Laing DDC Pump, 4x stainless steel screw M4x25.Note: With the addition of the 4 piece damper kit (not included but available using the in the drop down menu), the pump can be mounted in the hard drive cage or 80mm fan.
Description: The Alphacool Laing DDC Dual Attachment is an adapter to use two pumps together. By using two Laing DDC pumps in unison you can increase the overall pump output capacity by double. This is especially beneficial for long loops, parallel loops with multiple water blocks, or radiators and such with flow reducing channels. This is made possible by creating a chamber in which both pump's outflow are directed into the same outlet port. There are two inlet ports that "V" together or you can plug one of the ports and just use one single inlet. The two pumps will work together as if it was one larger pump while the attachment also allows for a small compact install within your case at the same time. Specifications: Dimensions: 87 x 67 x 20mm (L x W x H) Weight: ~100g Material: Plexiglass Mounting: 16x M4 thread Connections: 3 x G1/4 thread, 2 inlets, 1 outlet
